Product Code

Product description

Product Picture

Info

Product Position

LANTERN HEADER SCREWS

Used to secure the lantern header cleat to the lantern header beam.

INSERT FOR DECORATIVE CORNERS

Inserts into the DFCA

DECORATIVE FASCIA JOINTERS

This sits in the internal/ external corners of the decorative fascia inside conservatory against eaves beam

DENTIL ADD ON PROFILE

sits between eaves beam and lower window frames and acts as a female for the dentil moulding to fit to

DENTIL MOULDING

clips into dentil add on which is located above the frames and below the Eaves beam

EAVES BEAM CLEATS

Allows the jointing of two sections of eaves beam (two each corner are required if the roof has tie bar replacement kit on)

EAVES BEAM CLEAT SCREW - M5 X 12

To secure the eaves beam cleats into eaves beam

EAVES BEAM END PLUG

Located at the visible ends of the eaves beam, I.E. gable ended roofs

EAVES TRICKLE VENT

Attaches to the ventilated support trim to complete the vent

GABLE EAVES BEAM CORNER

Located at each end of the gable beam support to allow the fixing of starter bars.

ALUMINIUM GABLE BEAM

Acts as an eaves beam with a flat top to support gable frames.

GABLE INFILL WEDGE

Fill the triangle made when a gable section does not go to a point. optional extra for gable support beam

GABLE BEAM REINFORCEMENT

steel reinforcement bar sits inside of gable beam for extra structural support

GABLE BEAM TOP CLAD

Cladding which sits on the top of Gable beam.

GABLE INFIL WEDGE END CAP

gable infill wedge end cap sits between wedge and gable frame

COMPRESSION STRUT - LANTERN

Sits between lantern header and acts to support (stopping lantern beam from bowing towards each other)

LANTERN HEADER BEAM

used as the top 'eaves beam' on a lantern roof, also used for flat roof lantern roofs.

GLAZING END PROFILE TRIM

secured to the bottom of the glazing material to stop degradation of the glass and water penetration in the polycarbonate

V GROOVE FASCIA JOINTERS

Used as a jointer and sits in the internal/ external corners of the standard fascia.

V GROOVE FASCIA

Internal cladding which connects to the male connectors on the internal face of eaves beam

GLAZING SUPPORT TRIM

Locks in to parabolic head of eaves beam and has slots internal and external for the ventilation system

GLAZING SUPPORT TRIM

Locks in to the parabolic head of eaves beam

DROP ROD BRACKET SCREW - LANTERN

Required for fixing 5 way drop rod bracket to lantern header beam.

GABLE EAVES CORNER SCREW

used to fix GAC (gable eaves beam corner) and reinforcing  in gable beam

COMPRESSION STRUT SLEEVE SCREW - LANTERN

used to fix compression strut sleeve to compression strut

DECORATIVE ULTRASELECT FASCIA

connects to eaves beam and requires SFI insert

DECORATIVE ULTRASELECT INFILLS

slides inside decorative ultra select fascia

GEORGIAN RIDGE FIXING KIT - TBRK

Must be ordered with SSRK

DECORATIVE ULTRASELECT PLAIN FASCIA INFILL

sits in pocket of SFB - select fascia board

LANTERN EAVES CLEAT SCREW

used to secure eaves beam cleat in lantern header beam

LANTERN RING BEAM INTERNAL CLADDING

connects to the variable pitch lantern beam

STANDARD RIDGE FIXING KIT - TBRK

required for tie bar replacement kit

UNDER GUTTER TRIM

locates on the base of the standard eaves beam.

COMPRESSION STRUT BRACKET SCREW (LANTERN)

used to fix strut fixing bracket to variable pitch lantern beam

STANDARD EAVES BEAM

Light Eaves Is Only Available To Fabricators

Used as the base product of our roofs which fixes directly to the windows below

VICTORIAN FIXING KIT

used to fix eaves beam to window frames -cannot be used with dentil moulding

EAVES BEAM HIGH AND LOW PITCH PACKERS

used to 'pack out' the gap created between the glazing bar and the eaves. Used when the pitch of the roof is 5 to 10 and 35 to 40 degree

LANTERN BEAM CLEATS

used to connect variable lantern beam together

5 WAY DROP ROD BRACKET (BRACKET)

fixed to the underneath of the variable lantern beam for the tie bar drop rods

COMPRESSION STRUT FIXING BRACKET (LANTERN)

used to fix the compression strut to the variable lantern beam.

VARIABLE PITCH LANTERN BEAM

used as the lower section of a lantern/ orangery roof

LANTERN RAIN BAFFLE SEALING FOAM

adhered on the top side of the variable lantern beam header rain baffle